Reinforcement StraightRebar/ru

Инструменты армирования

U-Образная арматура

Архитектурный верстак "Arch"

Описание

This tool is part of the Reinforcement Workbench, an external workbench that can be installed with the Addon Manager.

Two sets of straight reinforcement bars inside an Arch Structure

Применение

1. Select any face of a previously created Structure object.
2. Then select Straight Rebar from the rebar tools.
3. A task panel will pop-out on the left side of the screen as shown below.
4. Select the desired orientation.
5. Give the inputs like 'Front cover', 'Right side cover', 'Left side cover', 'Bottom cover' and 'Diameter' of the rebar.
6. Select the mode of distribution either 'Amount' or 'Spacing'.
7. If spacing is selected, a user can also opt for custom spacing.
8. Pick Selected Face is used to verify or change the face for rebar distribution.
9. Click OK or Apply to generate the rebars.
10. Click Cancel to exit the task panel.

Task panel for the tool

Свойства

• ДанныеOrientation: It decides the orientation of the rebar (like a bottom, top, right and left).
• ДанныеFront Cover: The distance between rebar and selected face.
• ДанныеRight Cover: The distance between the right end of the rebar to right face of the structure.
• ДанныеLeft Cover: The distance between the left end of the rebar to the left face of the structure.
• ДанныеCover along: These property facilities the user to specify either top or bottom cover.
• ДанныеBottom Cover: The distance between rebar from the bottom face of the structure.
• ДанныеTop Cover: The distance between rebar from the top face of the structure.
• ДанныеAmount: The amount of rebars.
• ДанныеSpacing: The distance between the axes of each bar.

Программирование

See also: Arch API, Reinforcement API and FreeCAD Scripting Basics.

The Reinforcement StraightRebar tool can be used in macros and from the Python console by using the following function:

Rebar = makeStraightRebar(f_cover, coverAlong, rt_cover, lb_cover,
                          diameter, amount_spacing_check, amount_spacing_value, orientation="Horizontal",
                          structure=None, facename=None)

• Creates a Rebar object from the given structure, which is an Structure, and facename, which is a face of that structure.
  • If no structure nor facename are given, it will take the user selected face as input.
• f_cover, coverAlong, rt_cover, and lb_cover are inner offset distances for the rebar elements with respect to the faces of the structure.
  • f_cover is the frontal cover offset.
  • coverAlong is a tuple (position, value) that defines the offset value in one position (top, bottom, left, right) depending on the orientation.
  • rt_cover is either the right or the top cover offset, depending on the value of coverAlong and orientation.
  • lb_cover is either the left or the bottom cover offset, depending on the value of coverAlong and orientation.
• diameter is the diameter of the reinforcement bars inside the structure.
• amount_spacing_check if it is True it will create as many reinforcement bars as given by amount_spacing_value; if it is False it will create reinforcement bars separated by the numerical value of amount_spacing_value.
• amount_spacing_value specifies the number of reinforcement bars, or the value of the separation between them, depending on amount_spacing_check.
• orientation specifies the orientation of the rebar; it can be "Horizontal" or "Vertical".

Depending on the orientation of the rebar, the function can be called in two general ways by setting coverAlong appropriately.

The rebar is horizontal

Rebar = makeStraightRebar(f_cover, ("Top Side", value), right_cover, left_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Bottom Side", value), right_cover, left_cover, ...)

• coverAlong is a tuple with either a "Top Side" or a "Bottom Side" offset value.
• In this case rt_cover refers to the right_cover offset, and lb_cover refers to the left_cover offset.

The rebar is vertical

Rebar = makeStraightRebar(f_cover, ("Left Side", value), top_cover, bottom_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Right Side", value), top_cover, bottom_cover, ...)

• coverAlong is a tuple with either a "Left Side" or a "Right Side" offset value.
• In this case rt_cover refers to the top_cover offset, and lb_cover refers to the bottom_cover offset.

Example horizontal

import Arch, Draft, StraightRebar

Structure = Arch.makeStructure(length=1000, width=1000, height=400)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

Rebar = StraightRebar.makeStraightRebar(50, ("Bottom Side", 20), 100, 100,
                                        12, True, 5, "Horizontal", Structure, "Face4")
Rebar.ViewObject.ShapeColor = (0.9, 0.0, 0.0)

Rebar2 = StraightRebar.makeStraightRebar(50, ("Bottom Side", 50), 100, 100,
                                         12, True, 5, "Horizontal", Structure, "Face6")
Rebar2.ViewObject.ShapeColor = (0.0, 0.0, 0.9)

Example vertical

import Arch, Draft, StraightRebar

Structure2 = Arch.makeStructure(length=1000, width=1000, height=400)
Structure2.ViewObject.Transparency = 80
Draft.move(Structure2, FreeCAD.Vector(1500, 0, 0))
FreeCAD.ActiveDocument.recompute()

Rebar3 = StraightRebar.makeStraightRebar(50, ("Left Side", 20), 100, 100,
                                         12, True, 5, "Vertical", Structure2, "Face4")
Rebar3.ViewObject.ShapeColor = (0.9, 0.5, 0.0)

Rebar4 = StraightRebar.makeStraightRebar(50, ("Left Side", 50), 100, 100,
                                         12, True, 5, "Vertical", Structure2, "Face6")
Rebar4.ViewObject.ShapeColor = (0.0, 0.5, 0.5)

Edition of rebar

You can change the properties of the rebar with the following function:

editStraightRebar(Rebar, f_cover, coverAlong, rt_cover, lb_cover,
                  diameter, amount_spacing_check, amount_spacing_value, orientation,
                  structure=None, facename=None)

• Rebar is a previously created StraightRebar object.
• The other parameters are the same as required by the makeStraightRebar() function.
• structure and facename may be omitted so that the rebar stays in the original structure.

Пример:

import StraightRebar

StraightRebar.editStraightRebar(Rebar, 50, ("Top Side", 20), 100, 100,
                                24, True, 7, "Horizontal")

StraightRebar.editStraightRebar(Rebar2, 50, ("Top Side", 50), 100, 100,
                                24, True, 7, "Horizontal")

StraightRebar.editStraightRebar(Rebar3, 50, ("Right Side", 20), 100, 100,
                                24, True, 7, "Vertical")

StraightRebar.editStraightRebar(Rebar4, 50, ("Right Side", 50), 100, 100,
                                24, True, 7, "Vertical")

Инструменты армирования

U-Образная арматура

Архитектурный верстак "Arch"

BIM

• 2D drafting: Sketch, Line, Polyline, Circle, Arc, Arc by 3 points, Fillet, Ellipse, Polygon, Rectangle, B-spline, Bézier curve, Cubic Bézier curve, Point

---

• 3D/BIM: Project, Site, Building, Level, Space, Wall, Curtain Wall, Column, Beam, Slab, Door, Window, Pipe, Pipe Connector, Stairs, Roof, Panel, Frame, Fence, Truss, Equipment
  • Reinforcement tools: Custom Rebar, Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement
  • Generic 3D tools: Profile, Box, Shape builder..., Facebinder, Objects library, Component, External reference

---

• Annotation: Text, Shape from text, Aligned dimension, Horizontal dimension, Vertical dimension, Leader, Label, Axis, Axes System, Grid, Section Plane, Hatch, Page, View, Shape-based view

---

• Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid, Working Plane Top, Working Plane Front, Working Plane Side

---

• Modify: Move, Copy, Rotate, Clone, Create simple copy, Make compound, Offset, 2D Offset..., Trimex, Join, Split, Scale, Stretch, Draft to sketch, Upgrade, Downgrade, Add component, Remove component, Array, Path array, Polar array, Point array, Cut with plane, Mirror, Extrude..., Difference, Union, Intersection

---

• Manage: BIM Setup..., Views manager, Manage project..., Manage doors and windows..., Manage IFC elements..., Manage IFC quantities..., Manage IFC properties..., Manage classification..., Manage layers..., Material, Schedule, Preflight checks..., Annotation styles...

---

• Utils: Toggle bottom panels, Move to Trash, Working Plane View, Select group, Set slope, Create working plane proxy, Add to construction group, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, Toggle subcomponents, Survey, IFC Diff, IFC explorer, Create IFC spreadsheet..., Image plane, Unclone, Rewire, Glue, Reextrude
  • Panel tools: Panel, Panel Cut, Panel Sheet, Nest
  • Structure tools: Structure, Structural System, Multiple Structures
  • IFC tools: IFC Diff..., IFC Expand, Make IFC project, IfcOpenShell update
  • Nudge: Nudge Switch, Nudge Up, Nudge Down, Nudge Left, Nudge Right, Nudge Rotate Left, Nudge Rotate Right, Nudge Extend, Nudge Shrink

---

• Additional: Preferences, Fine tuning, Import Export Preferences, IFC, DAE, OBJ, JSON, 3DS, SHP

Документация пользователя

• Начинающим
• Установка: Загрузка, Windows, Linux, Mac, Дополнительных компонентов, Docker, AppImage, Ubuntu Snap
• Базовая: О FreeCAD, Интерфейс, Навигация мыши, Методы выделения, Имя объекта, Настройки, Верстаки, Структура документа, Свойства, Помоги FreeCAD, Пожертвования

---

• Помощь: Учебники, Видео учебники
• Верстаки: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework

---

• Addons: Менеджер дополнений, Внешние верстаки, Cкрипты и макросы

---

• Hubs: Уголок пользователя, Уголок опытных пользователей, Уголок разработчиков