Draft Snap/cs

Other languages:
Snap widget
Constrain
Draft

Description

Uchopování znamená "přilepení" následujících 3D bodu k existujícímu bodu. Uchopování je dostupné u většiny nástrojů v Kreslení a Architektuře a může být globálně zakázáno nebo povoleno příkazem Kreslení Přepínač uchopování

Snapping is available with most Draft and BIM commands.

Snapping to the endpoint of an edge

Snap tools

These tools are available in the Draft snap toolbar and in the Draft snap widget.

Note that circular edges do not have to be full circles.

  • Snap lock: enables or disables snapping globally.
  • Snap angle: snaps to the special cardinal points on circular edges, at multiples of 30° and 45°.
  • Snap extension: snaps to an imaginary line that extends beyond the endpoints of straight edges.
  • Snap parallel: snaps to an imaginary line parallel to straight edges.
  • Snap special: snaps to special points defined by the object.
  • Snap near: snaps to the nearest point on faces and edges.
  • Snap ortho: snaps to imaginary lines that cross the previous point at multiples of 45°.
  • Snap grid: snaps to the intersections of grid lines.

Advanced snapping

  • Additional snap points can be obtained by combining two snap options. For example combining Draft Snap Ortho and Draft Snap Extension will give you a snap point at the intersection of their imaginary lines.
  • Snapping can be combined with constraining.
  • Press D anytime during snapping to recenter the Working Plane onto the currently highlighted snap point. The working plane will jump back to its original position after the command has finished. introduced in 1.1
  • Press Q to insert a "hold point" at the current location of the cursor. You can snap to the orthogonal axes of hold points, and to the intersections of these axes. If the Draft Snap Midpoint option is active, you can also snap to the midpoint between two hold points.
  • Press ` one or more times to snap to an object that is obscured by other geometry. This is called "snap cycling". Note that you must move the cursor by a small amount in the 3D view after pressing the key.

Snap cycling 1: The red rectangle was created first therefore it has snap priority. Without snap cycling you cannot snap to the green rectangle where it is overlapped by the red rectangle.

Snap cycling 2: After using the snap cycle key once the green rectangle receives snap priority. Snapping to the midpoint of the overlapped green edge is now possible.

Notes

  • Multiple snap options can be active at the same time, but it is advisable to only activate the snap options you really need. Activating too many can slow things down.
  • 1.0 and below: It is not a good idea to have Draft Snap Near permanently active as it takes precedence over many other snap options.
  • introduced in 1.1: Is is possible to have Draft Snap Near permanently active, but it does mean you have to move the mouse more, and point the mouse more accurately, for other on-object snaps.

Preferences

See also: Preferences Editor and Draft Preferences.

Volby

  • Uzamknout: globálně přepíná uchopování na zapnuto/vypnuto
  • Určitá uchopovací místa mohou být získána kombinací 2 uchopovacích míst, např, Ortho + Prodloužení, která mají uchopovací bod na průsečíku jejich imaginárních přímek.
  • Další, mnohem komplexnější uchopovací místa mhou být získána použitím vazeb (stiskem kláves SHIFT nebo X nebo Y nebo Z během kreslení).
  • Stisknutí klávesy L během kreslení uzamkne aktuální úhel právě kresleného segmentu přímky.
  • Maximální vzdálenost, na kterou může být bod uchopovacím místem uchopen, je specifikována v předvolbách, ale také může být měněna za běhu stisknutím kláves [ nebo ].


Draft
User documentation