PartDesign Pad/cs

Úvod

Sketch (A) shown on the left; end result after pad operation (B) on the right.

Usage

1. Select a single sketch or one or more faces from the Body.
2. Press the Pad button.
3. Set the Pad parameters, see Options below.
4. Press the OK button.

Volby

Type

Rozměr

K poslední

K první

Až k ploše

Dva rozměry

Up to shape

introduced in version 1.0: The pad will extend up to the selected shape. Optionally press the Select shape button and select a shape. Leave the Select all faces checkbox enabled or disable it, press the Select faces button and select the faces up to which the pad should be created.

Offset to face

Offset from face at which the pad will end. This option is only available if Type is To last, To first or Up to face.

Length

Defines the length of the pad. This option is only available if Type is Dimension or Two dimensions. The length is measured along the direction vector, or along the normal of the sketch or face. Negative values are not possible. Use the Reversed option instead.

2nd length

Defines the length of the pad in the opposite direction. This option is only available if Type is Two dimensions.

Symmetric to plane

Check this option to extrude half the given length to either side of the sketch or face. This option is only available if Type is Dimension.

Reversed

Reverses the direction of the pad.

Direction

Direction/edge

You can select the direction of the extrusion:

• Sketch normal or Face normal: The sketch or face is extruded in the direction of its normal. If you have selected several sketches or faces to be extruded, the normal of the first one will be used.
• Select reference...: The sketch or face is extruded in the direction of a straight edge or a datum line selected from the Body.
• Custom direction: The sketch or face is extruded in the direction of the specified vector.

Show direction

If checked, the pad direction will be shown. In case the pad uses a Custom direction, it can be changed.

Length along sketch normal

If checked, the pad length is measured along the sketch or face normal, otherwise along the custom direction.

Taper angle

Tapers the pad in the extrusion direction by the given angle. A positive angle means the outer pad border gets wider. Note that inner structures receive the opposite taper angle. This is done to facilitate the design of molds and molded parts. This option is only available if Type is Dimension or Two dimensions.

2nd taper angle

Tapers the pad in the opposite extrusion direction by the given angle. See Taper angle. This option is only available if Type is Two dimensions.

Properties

Data

Pad

• ÚdajeType (Enumeration): Defines how the pad will be extruded, see Options.
• ÚdajeLength (Length): Defines the length of the pad, see Options.
• ÚdajeLength2 (Length): Second pad length in case the ÚdajeType is TwoLengths, see Options.
• ÚdajeUse Custom Vector (Bool): If checked, the pad direction will not be the normal vector of the sketch but the given vector, see Options.
• ÚdajeDirection (Vector): Vector of the pad direction if ÚdajeUse Custom Vector is used.
• ÚdajeReference Axis (LinkSub)
• ÚdajeAlong Sketch Normal (Bool): If true, the pad length is measured along the sketch normal. Otherwise and if ÚdajeUse Custom Vector is used, it is measured along the custom direction.
• ÚdajeUp To Face (LinkSub): A face the pad will extrude up to, see Options.
• ÚdajeOffset (Length): Offset from face in which the pad will end. This is only taken into account if the ÚdajeType option UpToLast, UpToFirst or UpToFace is used.
• ÚdajeTaper Angle (Angle)
• ÚdajeTaper Angle2 (Angle)

Part Design

• ÚdajeRefine (Bool): True or false. Cleans up residual edges left after the operation. This property is initially set according to the user's settings (found in Preferences → Part Design → General → Model settings).

Sketch Based

• ÚdajeProfile (LinkSub)
• ÚdajeMidplane (Bool)
• ÚdajeReversed (Bool)
• ÚdajeAllow Multi Face (Bool)

Omezení